The night the grid went quiet, and the small stuff that still worked
A chicken dust bath, a plastic that won't rot, and a radio that outlasts its legend. A thin day, but a hands-on one.
Start with the chicken dust bath, because it is the clearest lesson of the night. Ashley Adamant's recipe on Practical Self Reliance, published October 16, mixes four parts sand, four parts plain peat moss, two parts cold wood ash from clean, untreated firewood, and one part food-grade diatomaceous earth, all by volume. One batch makes about 5.5 gallons, enough to fill an 18.5-inch rubber tub four to five inches deep.
Each ingredient does a job. Hens clean themselves by rolling in loose, dry dirt to fluff their feathers. Sand does the scrubbing, but Adamant says sand alone does not cut mites enough. Peat moss strips stale feather oil, and a study she cites found hens new to dust bathing "ended up preferring peat over sand." Wood ash adds fine, clinging dust, and its alkalinity irritates parasites. That same alkalinity is why the recipe keeps ash to a smaller share, so it does not irritate the hens' own skin. Food-grade diatomaceous earth dries out mites and lice; she cites a UC study in which it cut them 80 to 100 percent within a week. Never pickling lime, hydrated lime or pool-filter diatomaceous earth, she warns, and mix it wearing gloves, eye protection and a dust mask.
The opposite lesson came from the compost heap. A maker going by "I built a thing" buried 3D-printed PLA in soil and compost for a year, through a European winter and a hot, dry summer, and Hackaday's Maya Posch wrote it up October 16. The samples showed no major visible damage and no statistically significant loss of tensile strength. Microcalorimetry at the University of Basel found microbes could not eat the material. PLA only biodegrades when it is pure and held at or above its glass transition temperature, conditions a garden never supplies. Even most industrial composters refuse printed parts. Options raised: re-extrude failed prints into fresh filament, switch to PHA, or print in PETG.
The rest of the day was about keeping machines alive. Julian Stargardt, writing on The SWLing Post, found a Tecsun H-501x out-receiving the classic Sony ICF-2010 on most shortwave measures. The Sony weighs 1.8 kg and runs on three D cells plus two AA; the Tecsun weighs 1.1 kg on two switchable 18650 lithium cells and needs only one to run. The Sony keeps one edge, synchronous detection Stargardt calls "good, very good," but he argues most listening rarely needs it.
Repairability was the quiet theme. An iFixit teardown of the Fairbuds 2 earbuds, also covered by Posch, showed a 3.6-volt LIR1054 coin cell that levers out by hand when you pull the battery door. No tools, no glue, yet still IP54 rated. iFixit scored it 10 out of 10; the one weak point is a USB-C port soldered straight to the board.
Two builds round out the night. A maker called Lazy_Duck soldered a working game controller, an RP2040-Zero, a joystick, buttons and a microswitch on plain protoboard in a printed case, for about €10, running the open GP2040-CE firmware. "The emphasis is on throwing things together, so there's no dedicated PCB." And for radio newcomers, Brent Conklin, W7BR, built a web page, Get Connected, that turns a few entries into a printable D-Star and hotspot setup sheet, one of three open-source tools flagged in a QRPer Notes roundup.
Sources
- Chicken Dust Bath (DIY Recipe and Ingredients) · Practical Self Reliance (Ashley Adamant)
- Disposing of PLA and Why Composting is Not an Option · Hackaday
- An Informal Hands-On Comparison of the Tecsun H-501x, Belka, and Sony ICF-2010/2001D · The SWLing Post (Thomas Witherspoon, K4SWL)
- Fairbuds 2 Teardown Shows Little Glue, Easy Battery Swap · Hackaday
- The 10€ Gamepad · Hackaday
- QRPer Notes: Open-Source MacOS TX-500 Utility App, D-Star and Hotspot Setup Assistance, and a Visual Path, Open-Source Browser-Based SDR App · QRPer (Thomas Witherspoon, K4SWL)