Off the grid, Nov 14
Tonight the fault is never dramatic: a knocked-off resistor, a burnt diode, a battery that will not wake, a table that is not level.
A Socket LGA 1851 mainboard that would not boot came back to life after a single 5.1-ohm resistor was soldered back onto the clock line beside its BIOS chip, Hackaday's Maya Posch reported on November 13. The Fix the Pixel channel worked through the power-up sequence. Power rails first, then the VRM controller's enable pin, which stayed low, and the trail led back to the chipset never reading the BIOS. A boardview file located the parts. A resistor knocked off the SPI clock line was the whole problem. Posch suggests checking those resistors before reaching for more advanced diagnostics.
That same patience shows up in a solar connection box. On DIY Solar Forum, ChrisinClevedon found a burnt diode in a 120-watt panel that had run a campervan for ten years, and asked whether the diode alone could be replaced. "This set-up has worked so well that I only replaced the batteries at 9 years old," the owner wrote. Elsewhere on the forum the trouble was a battery that would not wake: a 12-volt lithium pack drawn down too far on an electric fence now charges only to 12.4 volts and powers nothing, and its owner asks whether the battery management system is in protect mode and how to rouse it.
Thomas Witherspoon logged 34 Morse contacts in about 34 minutes at 5 watts on 40 meters from a North Carolina picnic area, the first ten in under nine minutes. The one free table sloped, and with only a mechanical bug for a key he found the slope matters. Gravity works on the bug's pendulum and upsets the timing of the dits. Farther down the dial, Dan Greenall reports that XERF, the Mexican border blaster once said to run 250 kilowatts on 1570 kHz, is still on the air at 100,000 watts, recorded November 10 through a Kiwi SDR near Monterrey.
At the bench, forum member bridger worked out in CAD that setting a lathe's compound slide at 30 degrees makes its dial read in diameter while the cross slide reads in radius, though he still accepts 29.5 degrees as better for threading. Another member, rwm, hit a plainer wall: sheet steel from a Steelcase drawer too thin to TIG without blowing through and impossible to spot weld from one side. "I can't spot weld because I can't get to the back side of the sheet," he wrote, weighing solder or a low-temperature braze.
Overhead, Astronomy Magazine's Alison Klesman points to Mirach in Andromeda, nearly 60 degrees high in the east by 7 p.m. and a signpost to what she calls Mirach's Ghost, with the Leonids peaking this week. And on November 17, NASA says via the Adafruit blog, Voyager 1 reaches one light-day from Earth, a distance, not a time, farther than anything built by human hands has gone in nearly 50 years.
The thread is the same one Ask a Prepper pulls on. What takes a person out of action is rarely dramatic: a fire that would not start, water nobody could trust, a cut nobody cleaned. The repairs gathered here are the same size. A resistor, a diode, a level table.
Sources
- Fixing a Dead Socket LGA 1851 Mainboard with a Resistor · Hackaday
- CFT1 Speaker Kit Upgrade’s First Field Test: My Bug-Out Month Send-Off · QRPer (Thomas Witherspoon, K4SWL)
- XERF 1570, Ciudad Acuna, Coahuila, Mexico, Then and Now · The SWLing Post (Thomas Witherspoon, K4SWL)
- Compound angle depth of cut · The Hobby-Machinist
- Joining Thin Sheet Metal · The Hobby-Machinist
- Can I just replace this diode on my campervan solar panel? · DIY Solar Forum
- wattcycle 12.8 100amp battery · DIY Solar Forum
- The Sky Today on Friday, November 13: Spot Mirach’s Ghost · Astronomy Magazine
- Shine bright for Voyager’s light-day · Adafruit Blog
- 15 High-Value Stockpiling Items Under $2 · Ask a Prepper